Hobby & Engineering Supplies - an MBA company

Thread Inserts Categories


Inserts - Thread Repair - Keylocking Starter Sets
Inserts - Thread Repair - Keylocking Starter Sets

Also see combined categories:
All Keylocking Inserts and Kits

Keylocking inserts are used to repair threads by tapping the worn thread to a standard larger thread, twisting the insert into place and then driving in the keys to lock the insert. Also known as keenserts.

Each kit contains an installation tool and the quantity of inserts shown. One size per kit. Also known as keenserts, keylocking inserts are available in mild steel and stainless steel. Installation is by drilling out the old thread, countersinking, tapping new thread with a standard tap, screwing the insert until slightly below the surface, then tapping down the keys using the tool supplied and a hammer. This category may be available in the new MBA online store at Inserts - Thread Repair - Keylocking Starter Sets.

Related Information:

There is also a good range of Inserts - Thread Repair - Keylocking Starter Sets on the Small Parts and Bearings website.


Inserts - Thread Repair - Recoil Starter Sets
Inserts - Thread Repair - Recoil Starter Sets

Also see combined categories:
All Recoil Inserts and Kits

Recoil inserts are screwed directly into an enlarged tapped hole. A tap and installation tool is included with these kits.

Stainless inserts. Contents: Ground intermediate (2nd) tap. Inserts. Installation/tang break off tool. Full instructions. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.

There is also a good range of Inserts - Thread Repair - Recoil Starter Sets on the Small Parts and Bearings website.


Inserts - Expansion - Press In - Brass
Inserts - Expansion - Press In - Brass

Also see combined categories:
All Expansion Inserts

Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.

Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability. Not as strong as wind-in inserts.

There is also a good range of Inserts - Expansion - Press In - Brass on the Small Parts and Bearings website.


Inserts - Expansion - Press In - Brass - Flanged
Inserts - Expansion - Press In - Brass - Flanged

Also see combined categories:
All Expansion Inserts

Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.

Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability. Not as strong as wind-in inserts.

There is also a good range of Inserts - Expansion - Press In - Brass - Flanged on the Small Parts and Bearings website.


Inserts - Self Tapping - For Aluminium - Steel
Inserts - Self Tapping - For Aluminium - Steel

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from steel with zinc chromate finish.

Related Information:

There is also a good range of Inserts - Self Tapping - For Aluminium - Steel on the Small Parts and Bearings website.


Inserts - Self Tapping - For Plastics - Steel
Inserts - Self Tapping - For Plastics - Steel

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Made from steel with zinc chromate finish.

Related Information:

There is also a good range of Inserts - Self Tapping - For Plastics - Steel on the Small Parts and Bearings website.


Inserts - Self Tapping - For Aluminium - Stainless 303
Inserts - Self Tapping - For Aluminium - Stainless 303

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can vary on batches. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from 303 stainless steel.

Related Information:

There is also a good range of Inserts - Self Tapping - For Aluminium - Stainless 303 on the Small Parts and Bearings website.


Inserts - Self Tapping - For Plastics - Stainless Steel
Inserts - Self Tapping - For Plastics - Stainless Steel

Also see combined categories:
All Self Tapping Inserts

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Provides a strong wear and vibration resistant thread. Use of installation tool recommended. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Standard made from 303 stainless steel. Quantity orders can also be supplied in Brass or 316 Stainless.

Related Information:

There is also a good range of Inserts - Self Tapping - For Plastics - Stainless Steel on the Small Parts and Bearings website.


Inserts - Self Tapping - For Wood - Hex Drive
Inserts - Self Tapping - For Wood - Hex Drive

Also see combined categories:
All Self Tapping Inserts
All Self Tapping Inserts for Wood

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Die Cast Zinc Alloy. Knife thread cuts easily into a predrilled hole. Inexpensive inserts for use in ready to assemble furniture, drawer pulls etc. Installs with a hex wrench. This category may be available in the new MBA online store at Inserts - Self Tapping - For Wood - Hex Drive.

There is also a good range of Inserts - Self Tapping - For Wood - Hex Drive on the Small Parts and Bearings website.


Inserts - Self Tapping - For Wood - Hex Drive - Flanged
Inserts - Self Tapping - For Wood - Hex Drive - Flanged

Also see combined categories:
All Self Tapping Inserts
All Self Tapping Inserts for Wood

Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.

Die Cast Zinc Alloy. Knife thread cuts easily into a predrilled hole. Inexpensive inserts for use in ready to assemble furniture, drawer pulls etc. Installs with a hex wrench. This category may be available in the new MBA online store at Inserts - Self Tapping - For Wood - Hex Drive - Flanged.

There is also a good range of Inserts - Self Tapping - For Wood - Hex Drive - Flanged on the Small Parts and Bearings website.


Threaded Rod - Allthread - Stainless Steel - 304
Threaded Rod - Allthread - Stainless Steel - 304

Also see combined categories:
All Threaded Rod

UNC - UNF - METRIC - 303 and 304 grades. Also known as booker rod.

This category may be available in the new MBA online store at Threaded Rod - Allthread - Stainless Steel - 304.

There is also a good range of Threaded Rod - Allthread - Stainless Steel - 304 on the Small Parts and Bearings website.


Bits - Insert
Bits - Insert


Insert bits for use with hand type screwdriver bit holders

This category may be available in the new MBA online store at Bits - Insert.

There is also a good range of Bits - Insert on the Small Parts and Bearings website.


Plungers - Ball - Threaded - Steel
Plungers - Ball - Threaded - Steel

Also see combined categories:
All Threaded Ball Plungers

Items shown with Long-Lok have a dry threadlocking sealant applied to thread. This category may be available in the new MBA online store at Plungers - Ball - Threaded - Steel.

There is also a good range of Plungers - Ball - Threaded - Steel on the Small Parts and Bearings website.


Nuts - Hexagonal - Nylon Insert - Aluminium
Nuts - Hexagonal - Nylon Insert - Aluminium

Also see combined categories:
All Lock Nuts

Nylon Insert for Locking. Not NylocTM brand.

Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. This category may be available in the new MBA online store at Nuts - Hexagonal - Nylon Insert - Aluminium.

Related Information:

There is also a good range of Nuts - Hexagonal - Nylon Insert - Aluminium on the Small Parts and Bearings website.


Nuts - Hexagonal - Nylon Insert - Stainless Steel
Nuts - Hexagonal - Nylon Insert - Stainless Steel

Also see combined categories:
All Lock Nuts

Nylon Insert for Locking. NylocTM and other brands.

Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. This category may be available in the new MBA online store at Nuts - Hexagonal - Nylon Insert - Stainless Steel.

There is also a good range of Nuts - Hexagonal - Nylon Insert - Stainless Steel on the Small Parts and Bearings website.


Tools - Die Holders
Tools - Die Holders

Also see combined categories:
All Tools

Bar and round holders. 16mm, 20.64mm and 25.4mm (inch). Also called a button die stock.

This category may be available in the new MBA online store at Tools - Die Holders.

There is also a good range of Tools - Die Holders on the Small Parts and Bearings website.


Tools - Die Nuts
Tools - Die Nuts

Also see combined categories:
All Dies
All Tools

Tungsten Chrome Alloy - Carbon Steel die nuts starting from M1 and 0-80 UNF. Many unusual sizes - M1.2, M1.4, M1.6, M1.7, BA Sizes, 2-56 and more. Sutton - PN - Bordo.

This category may be available in the new MBA online store at Tools - Die Nuts.

There is also a good range of Tools - Die Nuts on the Small Parts and Bearings website.


Tools - Tap Wrenches
Tools - Tap Wrenches

Also see combined categories:
All Tools

Tee handle and bar types. Suit taps from 1mm to 12mm.

This category may be available in the new MBA online store at Tools - Tap Wrenches.

There is also a good range of Tools - Tap Wrenches on the Small Parts and Bearings website.


Tools - Dies - Carbon Steel
Tools - Dies - Carbon Steel

Also see combined categories:
All Dies
All Tools

Tungsten Chrome Alloy - Carbon Steel Button dies and die nuts starting from M1 and 0-80 UNF. Many unusual sizes - M1.2, M1.4, M1.6, M1.7, BA Sizes, 2-56 and more. Sutton - PN - Bordo.

This category may be available in the new MBA online store at Tools - Dies - Carbon Steel.

There is also a good range of Tools - Dies - Carbon Steel on the Small Parts and Bearings website.


Tools - Taps - Carbon Steel - Hand
Tools - Taps - Carbon Steel - Hand

Also see combined categories:
All Taps
All Tools

Carbon Steel Straight Flute Taps. Starting from M1 and 0-90 UNF. Many unusual sizes - M1.2, M1.4, M1.6, M1.7, BA Sizes, 2-56 and more. Sutton - PN - Bordo.

Carbon steel hand taps. Carbon Steel (CS) Hand taps. This category may be available in the new MBA online store at Tools - Taps - Carbon Steel - Hand.

There is also a good range of Tools - Taps - Carbon Steel - Hand on the Small Parts and Bearings website.


Screws - Hex Head - Steel - Zinc Plated - Full Thread
Screws - Hex Head - Steel - Zinc Plated - Full Thread

Also see combined categories:
All Hex Head Screws

BSW and METRIC - Set Screws

This category may be available in the new MBA online store at Screws - Hex Head - Steel - Zinc Plated - Full Thread.

Related Information:

There is also a good range of Screws - Hex Head - Steel - Zinc Plated - Full Thread on the Small Parts and Bearings website.


Screws - Hex Head - Brass
Screws - Hex Head - Brass

Also see combined categories:
All Machine Screws
All Brass Machine Screws

Brass metal thread machine screws UNC and UNF

Nuts sold seperately - See Nuts. This category may be available in the new MBA online store at Screws - Hex Head - Brass.

Related Information:

There is also a good range of Screws - Hex Head - Brass on the Small Parts and Bearings website.


Screws - Pan Head - Steel - Philips
Screws - Pan Head - Steel - Philips

Also see combined categories:
All Machine Screws

Metal Thread Screws UNC - UNF - METRIC

Nuts sold seperately - See Nuts. This category may be available in the new MBA online store at Screws - Pan Head - Steel - Philips.

Related Information:

There is also a good range of Screws - Pan Head - Steel - Philips on the Small Parts and Bearings website.


Screws - Round Head - Brass - Slotted
Screws - Round Head - Brass - Slotted

Also see combined categories:
All Machine Screws
All Brass Machine Screws

Brass metal thread machine screws BSW - UNF - UNC

Nuts sold seperately - See Nuts. This category may be available in the new MBA online store at Screws - Round Head - Brass - Slotted.

Related Information:

There is also a good range of Screws - Round Head - Brass - Slotted on the Small Parts and Bearings website.


Screws - Hex Head - Titanium CP Grade 1
Screws - Hex Head - Titanium CP Grade 1

Also see combined categories:
All Hex Head Screws

Fully threaded hex head set screws (DIN933). CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.

Din 933. Commercially pure for general industrial corrosion applications. UNS R50250. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance. This category may be available in the new MBA online store at Screws - Hex Head - Titanium CP Grade 1.

Related Information:

There is also a good range of Screws - Hex Head - Titanium CP Grade 1 on the Small Parts and Bearings website.


Screws - Pan Head - 303-304 Stainless - Philips
Screws - Pan Head - 303-304 Stainless - Philips

Also see combined categories:
All Machine Screws

Metal Thread Screws UNC - UNF - METRIC - Pan, cheese, fillister and round head.

Nuts sold seperately - See Nuts. This category may be available in the new MBA online store at Screws - Pan Head - 303-304 Stainless - Philips.

Related Information:

There is also a good range of Screws - Pan Head - 303-304 Stainless - Philips on the Small Parts and Bearings website.


Screws - Pan Head - Titanium CP Grade 1 - Philips Drive
Screws - Pan Head - Titanium CP Grade 1 - Philips Drive

Also see combined categories:
All Machine Screws

Metal Thread Screws. Metric only. CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.

Nuts sold seperately - See Nuts. Commercially pure for general industrial corrosion applications. UNS R50250. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance. This category may be available in the new MBA online store at Screws - Pan Head - Titanium CP Grade 1 - Philips Drive.

Related Information:

There is also a good range of Screws - Pan Head - Titanium CP Grade 1 - Philips Drive on the Small Parts and Bearings website.


Screws - Self Tapping - For Soft Plastics - Pan Head
Screws - Self Tapping - For Soft Plastics - Pan Head

Also see combined categories:
All Self Tapping Screws
All Self Tapping Screws for Plastics

Tri-Lobe Course Thread Plastic Threading Screws

Thread cutting screws for plastics. Be sure to select correct screw for hard or soft plastic threadcutting. This category may be available in the new MBA online store at Screws - Self Tapping - For Soft Plastics - Pan Head.

There is also a good range of Screws - Self Tapping - For Soft Plastics - Pan Head on the Small Parts and Bearings website.


Knobs - Pointer - Skirted
Knobs - Pointer - Skirted

Also see combined categories:
All Pointer Knobs

Grub screw fixing. Suits 6.35mm (1/4 inch) shaft. Brass insert.

This category may be available in the new MBA online store at Knobs - Pointer - Skirted.

Related Information:

There is also a good range of Knobs - Pointer - Skirted on the Small Parts and Bearings website.


Screws - Countersunk - Socket - Steel
Screws - Countersunk - Socket - Steel

Also see combined categories:
All Countersunk Screws

Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel

Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991. Rc38-42. ASTM F835 - alloy steel. ISO 10642. The thread length indicated is the minimum. Some batches may be produced with longer threaded sections or even full threaded shanks.

Related Information:

There is also a good range of Screws - Countersunk - Socket - Steel on the Small Parts and Bearings website.


Screws - Self Tapping - For Hard or Soft Plastics - Pan Head
Screws - Self Tapping - For Hard or Soft Plastics - Pan Head

Also see combined categories:
All Self Tapping Screws
All Self Tapping Screws for Plastics

Tri-Lobe Course Thread Plastic Threading Screws

Thread cutting screws for plastics. Be sure to select correct screw for hard or soft plastic threadcutting. This category may be available in the new MBA online store at Screws - Self Tapping - For Hard or Soft Plastics - Pan Head.

There is also a good range of Screws - Self Tapping - For Hard or Soft Plastics - Pan Head on the Small Parts and Bearings website.


Tools - General
Tools - General

Also see combined categories:
All Tools

Butane Torch, Inspection Mirror, Mini Sandblaster, Nibbling Tool, Plastic Scriber, Pick Up Tool Set, Hex Driver Handle for Insert Bits

X-Acto Knife Sets - Pin Vises - Screw Pitch Gauges and more. This category may be available in the new MBA online store at Tools - General.

There is also a good range of Tools - General on the Small Parts and Bearings website.


Nuts - Blind
Nuts - Blind

Also see combined categories:
All Nuts

Blind nuts - Tee nuts.

Put steel threads in soft materials like wood without counterboring. This category may be available in the new MBA online store at Nuts - Blind.

There is also a good range of Nuts - Blind on the Small Parts and Bearings website.


Screws - Countersunk - Socket - Titanium Ti-Gr5 - Ti-6Al4v - DIN7991
Screws - Countersunk - Socket - Titanium Ti-Gr5 - Ti-6Al4v - DIN7991

Also see combined categories:
All Countersunk Screws

Flat Head Countersunk. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.

Metric Sizes to DIN7991. Used in critical aircraft structural components. UNS R56400. ISO 10642. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent. The thread length indicated is the minimum. Some batches may be produced with longer threaded sections or even full threaded shanks.

Related Information:

There is also a good range of Screws - Countersunk - Socket - Titanium Ti-Gr5 - Ti-6Al4v - DIN7991 on the Small Parts and Bearings website.


Screws - Countersunk - Socket - 304 Stainless
Screws - Countersunk - Socket - 304 Stainless

Also see combined categories:
All Countersunk Screws

Flat Head Countersunk UNC - UNF - METRIC - Stainless Steel

Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991. ISO 10642. The thread length indicated is the minimum. Some batches may be produced with longer threaded sections or even full threaded shanks. This category may be available in the new MBA online store at Screws - Countersunk - Socket - 304 Stainless.

Related Information:

There is also a good range of Screws - Countersunk - Socket - 304 Stainless on the Small Parts and Bearings website.


Bungs and Caps - Reversible - Round
Bungs and Caps - Reversible - Round


Tapered plastic bungs fit inside round tube or over the outside ends of rod, tube or shafting.

Can be used on threaded or unthreaded parts. Used as tuning bungs or rod tips. Helps prevent damage to the product ends. Helps prevent injury from sharp edges. This category may be available in the new MBA online store at Bungs and Caps - Reversible - Round.

Related Information:

There is also a good range of Bungs and Caps - Reversible - Round on the Small Parts and Bearings website.


Nuts - Hexagonal - Brass
Nuts - Hexagonal - Brass

Also see combined categories:
All Nuts

UNC - UNF - BA - METRIC.

Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. Nuts marked as type SCALE have the same dimension across flats as the brass hex head screw of the same thread size. This category may be available in the new MBA online store at Nuts - Hexagonal - Brass.

There is also a good range of Nuts - Hexagonal - Brass on the Small Parts and Bearings website.





Main Pages

About Us Acetal Bearings PDF ADR and SKF PDF Anderton Circlips Cross Reference PDF Ball Lock Pins PDF Balls List Balls PDF Barden Bearings Cross Reference PDF Bearings List Brands Catalogue Ceramic Bearings PDF Circlips PDF Clearance Items List Clevis Pins PDF Contact Us Charity Corrosion Resistant Bearings PDF Disc Springs PDF Dowel Pins PDF Economy Bearings PDF Essentra Cross Reference PDF Flocast Cross Reference PDF Freight Rates and Shipping Times Frequently Asked Questions General Information about MBA Hammer Drive Pins PDF High Speed Bearings PDF Hobby Clearance Hobby Information K&S Metals Cross Reference PDF Key Steel PDF Knobs PDF Large Bearings Leveling Mounts PDF Mailorder Form Metallic Bushes PDF Miniature Precison Bearings Cross Reference PDF Miscellaneous Brands Cross Reference PDF Nordex Cross Reference PDF NSK and NTN Cross Reference PDF Ondrives Cross Reference PDF O-Rings PDF Pins PDF Plastic Bearings PDF Polyvee Belts and Pulleys PDF Precision Shim Washers PDF Privacy Push On and Push In Rings PDF Reid Supply Cross Reference PDF Rod & Tube PDF Roll Pins PDF Screws PDF SDP-SI Designatronics Cross Reference PDF Seeger Circlips Cross Reference PDF Shaft Collars PDF Shim Sheet PDF Shoulder Screws PDF Sintered Bronze Bushes PDF Sintered Bronze Cross Reference PDF Small Bearings Small Parts Inc Cross Reference PDF Snap Rings PDF Socket Set Screws PDF Solid Bronze Bushes PDF Spring Steel Strip PDF Springs PDF Standard Ball Bearing Range PDF Super Precision Bearings PDF Taper Pins PDF Technical Information Terms Thrust Bearings PDF Thumb Screws and Nuts PDF Timing Belts and Pulleys Cross Reference PDF Timing Belts PDF Timing Pulley Stock PDF Timing Pulleys PDF Vibration Mounts PDF Washers and Spacers PDF Wave Washers PDF Domains


Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Hobby & Engineering Supplies Pty Ltd (ABN 54 125 001 541)

Hobby and Engineering Supplies offers 5836 products in 246 categories including low priced hobby bearings, screws, brass and aluminium rod and tubing, shim - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Hobby and Engineering Supplies is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Hobby and Engineering Supplies 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Hobby & Engineering Supplies Pty Ltd (ABN 54 125 001 541)

Hobby and Engineering Supplies offers 5836 products in 246 categories including low priced hobby bearings, screws, brass and aluminium rod and tubing, shim - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Hobby and Engineering Supplies is part of MBA Group offering a select range from the MBA Group catalogue.

Information on this website is Copyright Hobby and Engineering Supplies 1997. All rights reserved.