Vee Belts Categories

Belts - Vee - 10.0 x 5.5mm - M-3L

Also see combined categories:
All Vee Belts 8mm and 10mm Top Width

Miniature and small belts. 10.0mm Top Width x 5.5mm Height.

Sizes are nominal and may vary slightly. Items marked as Fractional Horsepower are designed for general purrpose low horseposer applications such as laundry machines, home workshop tools, small fans and blowers, garage equipment, small metal and woodworking tools etc. Belts shown as Fractional Horsepower type should not be used with reverse side idlers.

Related Information:

Vee Pulleys - Idler

Vee Pulleys - M / 3L Section - Aluminium

Vee Pulleys - M / 3L Section - Cast Iron

There is also a good range of Belts - Vee - 10.0 x 5.5mm - M-3L on the Small Parts and Bearings website.

Belts - Vee - 8.0 x 4.0mm

Also see combined categories:
All Vee Belts 8mm and 10mm Top Width

Miniature and small belts. 8.0mm Top Width x 4.0mm Height.

Sizes are nominal and may vary slightly.

Related Information:

Vee Pulleys - Idler

There is also a good range of Belts - Vee - 8.0 x 4.0mm on the Small Parts and Bearings website.

Belts - Vee - 10.0 x 6.0mm - Z

Also see combined categories:
All Vee Belts 8mm and 10mm Top Width

Miniature and small belts. 10.0mm Top Width x 6.0mm Height.

Sizes are nominal and may vary slightly.

Related Information:

Vee Pulleys - Idler

There is also a good range of Belts - Vee - 10.0 x 6.0mm - Z on the Small Parts and Bearings website.

Belt CP E-Sky Parts

Bearings and Spare Parts for Remote Control Models

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

Belts - Timing - 5.080mm Pitch - XL - 7.9mm Wide

Also see combined categories:
All XL 5.08mm Pitch Timing Belts

Standard Series Timing Belts 5.080mm or 0.200 inch pitch.

Breaking strength is not indicative of working strength. Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.30mm. Belt Height (W) - 2.30mm - Corner Radii ( r ) - 0.40mm. Pitch (P) - 5.080mm (0.200 inch).

Related Information:

All 5.08mm XL Pitch Timing Pulleys - Choose width carefully

Timing Belts Catalogue PDF

There is also a good range of Belts - Timing - 5.080mm Pitch - XL - 7.9mm Wide on the Small Parts and Bearings website.

KA85 Belt Sander Black and Decker Parts

Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

There is also a good range of KA85 Belt Sander Black and Decker Parts on the Small Parts and Bearings website.

BSG-151 Belt Sander Ozito Parts

Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

There is also a good range of BSG-151 Belt Sander Ozito Parts on the Small Parts and Bearings website.

BSR-1000 Belt Sander Ozito Parts

Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

There is also a good range of BSR-1000 Belt Sander Ozito Parts on the Small Parts and Bearings website.

BSR-800 Belt Sander Ozito Parts

Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

There is also a good range of BSR-800 Belt Sander Ozito Parts on the Small Parts and Bearings website.

1-10 Belt Drive Colt Parts

Bearings and Spare Parts for Remote Control Models

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

TA03 - TA03F Chassis Belt Drive Tamiya Parts

Bearings and Spare Parts for Remote Control Models

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

Freejet Hoover Parts

Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

There is also a good range of Freejet Hoover Parts on the Small Parts and Bearings website.

Multi Models Dyson Parts

Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

There is also a good range of Multi Models Dyson Parts on the Small Parts and Bearings website.

RC Spare Parts - Great Vigor

Great Vigor spare parts listed by description. Parts to suit 1/10 scale, 1/6 scale, Buggies, Truggies, 2WD, 4WD, BV1, Cage Buggy, Belt Crusher, Electrafun, Nitro Cage, Hunter Buggy, Rex-x

There is also a good range of RC Spare Parts - Great Vigor on the Small Parts and Bearings website.

RC Spare Parts - Venom

Venom Hobby Parts listed by description. Parts for 1/10 crawler, Baja, 1/8 scale cars, Beacon, Corsair, CPR Creeper, D Micro, DXL, EKOS, EPO, GPV-1, MINIZ, Island Hopper, King, Segad, KOS, KWA, M05, ME-109, MTT, Night Ranger 3D, Outlaw RC, Ozone Heli

Parts also to suit P-51, Texan, Savage, Scorpion AX10, Skywolf 3CH, Strait Jacket, TraXXas, TRX Slash. Ailerons fittings, Anti-rotation arm, A arms, Axle, Bag, Ball end, batteries assembleys, battery(bags, bars, box, case, charger, holder), beadlock, bearing kits, retainers and set. bell crank, blade grips and sets, body posts, bolt, bracket, bulkhead, cables, camber gauge, canopy, caps, carburettor, charger, chassis covers and plates. Cockpit cover, Collars, connectors, control links, control links, tray and units, coupler, cowl, crankcase, crankshaft, cylinder, Damper, decal set, differential (case, housing and system). Dig unit, drive (belt and dog), driveline, electronics unit, elevator, e-ring, ESC, exhaust (coupler, deflector and pipe), fail safes, feathering spindle.

There is also a good range of RC Spare Parts - Venom on the Small Parts and Bearings website.

Shims - Rubber

Handy non marring soft spacer shims in a wedge shape

Level and stabilise appliances, desks, tables, filing cabinets, machinery. Stackable. Vibration cushioning. Ribs ensure that wedges grab tight and stay in place. Black ridid wedges can support up to 2000 lbs. White flexible wedges can be trimmed with a utility knife.

There is also a good range of Shims - Rubber on the Small Parts and Bearings website.